|For at se vore priser skal du være oprettet som kunde: Er du allerede oprettet som kunde skal du logge ind.
MATROX MC-100 Mini Converter (MC-100)
||Type: Video Converter
|Ring for lager|
Dual SDI to HDMI Mini Converter for 3G/3D/HD/SD
As a broadcast engineer or A/V professional you likely have diverse needs when it comes to managing SDI signals within your environment - for monitoring, distributing, switching, multiplexing, and processing 3D in real time. Until now, you have been forced to purchase different devices to perform these tasks. The new Matrox MC-100 solves all these challenges in one inexpensive, easy-to-use device.
Matrox MC-100 is a dual SDI to HDMI mini converter that supports a wide range of display resolutions through 3G, Dual Link, HD, and SD-SDI. This single portable unit can be used as a HD-SDI switcher, a distribution amplifier, a multiplexer, and a 3D processing unit, making it the most versatile mini converter on the market. It should be in every video professional's toolbox.
Monitor SDI on inexpensive HDMI displays
Take your SDI video signal with 16 channels of embedded audio and convert it to HDMI. Whether you're using RGB or YUV, Matrox MC-100 maintains the full 10-bit video spectrum of the signal, up to a resolution of 1920 X 1080. Eight channels of embedded audio are supported on HDMI, selectable between the first and second set of 4 pairs.
Configure using On-Screen-Display
Quickly and efficiently configure your Matrox MC-100 via the on-screen-display (OSD) menu available on all outputs. There is no need for a computer connection. Every MC-100 feature is accessible through the OSD, which is controlled by three buttons directly on the unit. User-defined presets can be saved to dip switches for even quicker setup.
Distribute and amplify SDI signals
Configure MC-100 as a distribution amplifier to boost the strength of your SDI signals by 300 meters on SD-SDI, 100 meters on HD-SDI, and 70 meters on 3G-SDI. Duplicate a single SDI input signal to two independent, amplified signals.
Switch between two SDI signals
Toggle between two SDI inputs at the touch of a button, glitch-free as per SMPTE RP-168. MC-100 is also a loss-of-signal switcher. You can configure the device to automatically switch to the second valid input if the first one is lost or becomes invalid. As an added benefit, the LEDs on MC-100 illuminate green or red depending on signal validity.
Multiplex two SDI signals into one 3G video feed
Transport your SDI signals efficiently using MC-100 to multiplex two HD-SDI signals into a single 3G-SDI stream. On the receiving end, a second MC-100 or another SMPTE-425M compatible device demultiplexes the signal, providing two independent HD-SDI video signals. Being able to multiplex two SDI signals means that you'll need just half the wiring to distribute HD-SDI video signals.
Process and monitor 3D SDI signals in real time
Use the cutting-edge processing power of MC-100 to make multiple adjustments on stereoscopic video feeds in real time. Hardware buttons let you perform Horizontal Image Translation (HIT)—pixel-based convergence and divergence—on both video inputs. The images can be flipped horizontally and/or vertically, with pixel-based offset controls. Monitoring 3D content can be done on the HDMI or SDI outputs, with several analysis modes such as anaglyph, difference and 50/50. The signal can then be sent on a single SDI cable as a side-by-side or an over/under feed. On HDMI it can be sent in side-by-side, over/under, or frame packing mode. MC-100 also features a built-in video frame synchronizer that is useful for 3D production. When you define one of the video inputs as the reference source, the unit time base corrects the second video input and outputs the two video streams in sync.
||Length 125 mm
Width 118 mm
Height 26 mm
|Inputs and Outputs
||Two BNC 3G/HD/SD-SDI inputs
Two BNC 3G/HD/SD-SDI outputs
Mini USB Type B for firmware updates
||SDI compliance with SMPTE-259M/292M/372M/424M/425M
SDI support of YUV 4:2:2 8-bit/10-bit
SDI redundant inputs with loss-of-signal switcher
Automatic SDI output selection between 3G/HD/SD-SDI dependent on input signal
HDMI support of YUV 4:2:2, and RGB
|Advanced Features||Glitch-free switching as per SMPTE RP-168
Multiplexing of two HD-SDI signals over a single 3G cable as per SMPTE-425M level B
Vertical and/or horizontal flips on both video channels
Pixel-based convergence adjustments on both video channels
Pixel-based vertical offsets on both video channels
Video time base corrector and frame synchronizer using SDI1 or SDI2 as reference input
|Input Display Resolutions
1080p (Level A) 50/59.94/60
1080p (Level B) 50/59.94/60
1080p Dual link 50/59.94/60
||3D display formats on SDI: Over/Under, Side-by-Side
3D display formats on HDMI: Over/Under, Side-by-Side
Analysis display modes: Anaglyph, 50/50, Difference
||SDI audio: 16 channels embedded
HDMI audio: 8 channels embedded,
selectable between the first and second set of 4 pairs
|Electrical and Operating Requirements
||Unit voltage and amperage: 5V/3Amps
Operating temperature: 0 to 40º C
Storage temperature: -40 to 75º C
Maximum altitude for operation: 3,000 meters
Maximum altitude for transport: 12,000 meters
Operating humidity: 20 to 80% relative humidity (non-condensing)
Storage humidity: 5 to 95% relative humidity (non-condensing)
||Universal power supply with international socket adapters included
3-year limited manufacturing warranty
Selvom vi gør vort bedste for at give fyldestgørende information, så er billederne kun vejledende, og selve varen er ikke nødvendigvis 100% identisk med det viste billede. Produkter kan være vist med ekstraudstyr der ikke er inkluderet eller i andre form- og farvevarianter. Hvis der er forskel mellem produktoverskrift, beskrivelse og billede, så er det produktoverskriften som gælder. Hvis du er i tvivl, så kontakt os gerne. Vi tager forbehold for trykfejl, ændring af priser og specifikationer uden varsel.